Roof Repair Highland Village TX Can Help Fix Leaky Roofs
February 27, 2017
Roof Replacement Corinth TX Options for a Flat Roof Need to Be Assessed
March 19, 2017
Show all

Roofing in Highland Village TX: Do You Know What Flashing Does?

Each raised nuance that is a part of your roofing in Highland Village TX needs to be completely covered to keep water and other materials

roofing in highland village tx

from getting in. The most common type of roofing material used for this purpose is flashing. It helps to protect the roof beneath the nuance that is raised up off of your roof. It helps to guide any water that lands on your roof to the appropriate parts of your roof, instead of allowing that water to seep into your home’s attic space. If you are doing any roofing repairs or replacing your roof in Denton, Texas, consider if your flashing is still in good condition.

Flashing is an Integral Part of Your Roofing in Highland Village TX

Every roof has openings. They can be there for regular things like dormers, or they can be there for optional items like skylights. Each opening has the potential to allow water and other outside materials to come into your home. If you do not have a way to protect the opening, you could wind up with things like a leaky roof and moldy insulation. To avoid this type of problem, you have to keep each opening fully protected.

Flashing Sits Around Openings Yet Under Shingles

When you have to cut a hole in your roof for any purpose, you need to use f under the roofing materials to tell the water where to run. It also helps protect the seams between the roof and the item that is raised from your roof from infiltration by such things as animals. It is much harder for a squirrel to burrow through metal flashing than it would be to dig through plywood and felt paper. If you notice a leak around any of the extra openings in your roof, the flashing is the best place to start looking.

Flashing is used for many different improvements that are made to roofs. If you have dormers, as previously mentioned, flashing is typically used at the top of the window, down both sides of the dormer, and there is often an apron that extends beyond the bottom of the window. This helps the water know where to go so it does not seep into your home, and keeps your roofing materials from getting damaged by the rain.

Every raised vent in your roof will also need to be surrounded by flashing. The goal of the vents is to let some of the pent up heat from the Denton, Texas sun escape from your roof. This keeps your home cooler and keeps your energy costs down. If you opt for hooded vents, the flashing will be slid up beneath the other roofing materials to protect the opening. However, if you choose a pipe vent, you will need to meet different flashing requirements. Once the pipe is cut into the roof and the shingles, your flashing will need to extend six inches to both the left and right, eight inches above the hole, and another four inches below the hole. That is the only way to protect the hole from water seepage.

When you have a chimney, you will have different roofing and flashing requirements as well. Chimneys need to be protected from all sides, but also up the brickwork. Your roofing materials need to be set up differently, as the water can seep down the bricks and into your attic space. In the case of a chimney, you need flashing that goes from the roof up the sides of the chimney, and flashing that covers the corners of the chimney itself. This helps to protect the roofing materials around the chimney, as well as the mortar and bricks themselves on the chimney, from damage.

Skylights also need to have a wide berth of flashing put into your roofing materials. Typically, skylights are made with the flashing already attached by the time they are delivered. However, this does not mean that you are getting the right amount of flashing to protect your roofing materials. You should try and have at least eight inches both directions vertically so that you can keep the water from hitting the top of the skylight and seeping in. You should also have flashing down the sides to direct all water from trying to come inside your home around the skylight.

Roofing Materials Need to Be Used in Conjunction to Work Right

In order to protect all aspects of your roof, you need to make sure you are using the proper roofing materials to begin with. Flashing is made to protect your home from leaks, and needs to be used any time you add anything to your roof that sticks up vertically. If you are not sure how to properly use flashing around any opening in your roof, then call in roofing experts. That way, you get the job done right, and you have the peace of mind that your home will not become a wading pool the next time it rains.

If you need help with getting your roofing materials in the right order, contact First Out Roofing. They can come to your Denton, Texas home by simply calling (940)227-4411 today!